Iniciar sesión:
Votos - 4, Puntuación media: 4 ( )

Manual de usuario Clarity, modelo XL-25S

Fabricar: Clarity
Tamaño del archivo: 1.28 mb
Nombre del archivo: 96ffd16e-4d5e-4fad-9897-02341e13546b.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página

Resumen del manual

Figure 9 - Volume Slide Control Note: In standard use of the XL-25s, the amplifier turns off whenever you hang up the telephone. This is a useful feature if many people use the phone. If you want the amplifier to always remain on at the most recent volume setting, slide the switch on the bottom of the phone, as shown in Figure 10. Figure 10 - Internal Amplifier On/Off Using Your XL-25s Using Your XL-25s Incoming Voice Volume The XL-25s provides extra volume (12dB) to increase incoming sound. To increase incoming sound: 1. Adjust the IN VOL slide control in Figure 11 to suit your hearing. Figure 11 - Tone Slide Control Ringer Volume and Pitch 1. You can adjust the RINGER VOLUME as high as 75 decibels. The settings available are OFF, LO and HI as shown in Figure 12. TP Figure 12 - Ringer Volume & Pitch 2. The RING TONE has two pitch settings: LO and HI. Hold To put the line on hold, press the HOLD button and return the handset to its cradle. You will notice the red indicator light comes on. Note: If you pick up an extension phone on the same line when the XL-25s is on HOLD, the line will disconnect and you can continue your conversation on the extension phone. Figure 13 - Hold Button Last Number Redial To redial the last number dialed with the XL-25s phone, lift the handset and press REDIAL. E N G L I S H Using Your XL-25s Using Your XL-25s Figure 14 - Redial Button Flash Press the FLASH button shown in Figure 15 to access special services available from your local phone company such as Call Waiting and 3-Way Calling. PostScript Picture (FLASHBUT.TON) Figure 15 - Flash Button Special Features E N G Special Features E N G Programming the Memory Buttons You can automatically dial twelve programmed telephone numbers using the memory buttons shown in Figure 16. Each button can be programmed (or reprogrammed using the same procedure) for a phone number up to 16 digits long. X Figure 16 - Memory Buttons To program a button, follow these steps: 1. Lift the handset and press PROG as shown in Figure 17. Figure 17 - PROG Button L 2. Enter the phone number on the I keypad (Figure 18) just as you S would dial it normally. H Figure 18 - Telephone Keypad 3. Press PROG (Figure 17) once again. 4. Press a memory button (Figure 16) to store this number on that button. 5. Immediately hang up the handset. Note: Any number previously stored at that button number will be overwritten. 6. To change a stored number, repeat the programming process starting with step 1. Special Features Special Features Direct Audio Output The AUDIO OUTPUT socket allows you to connect the XL-25s audio output to an assistive listening devices. Figure 19 - Audio Output Socket To use this port, plug in a compatible auxiliary cable and connect it to your assistive listening device. Speak into the handset when you use the Audio Output connection. Troubleshooting Chart Specifications Troubleshooting Chart Specifications The chart below will help you solve most problems that may arise during operation of your telephone. Should the difficulty continue, contact Clarity at (800) 426-3738 or your authorized dealer for assistance. SYMPTOM CAUSE AND CORRECTIVE ACTION No dial tone Check all phone cord connections. No number No number stored dialed when in that memory memory button. See: button pressed “Programming the Memory buttons”. Call cannot See “Setting Up be dialed, or Your Phone” to dials very reset the dial slowly mode switch. An incoming Make sure the call does not ringer is not set to produce an the OFF position. audible ring Ring flasher not very bright Check and replace the 9 Volt battery Outgoing Volume Control 0 - 18dB Incoming Volume Control 0 - 12dB Dimensions Size: 91/2" x 7" x 31/4" Weight: 2.52 lbs. Power Requirements One 9 Volt alkaline battery for ring flasher operation only. (not included) E N G L I S H Regulatory Compliance Regulatory Compliance Part 68 of FCC Rules Information This equipment complies with Part 68 of the FCC rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug, RJ11 USOC, is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local...


Tu reseña
Tu nombre:
Introduzca dos números de la imagen: