Iniciar sesión:
Clasificado: Nombre ↑   Descargas   Tarifa   Tamaño ↑  
Descargado: 21   Tamaño del archivo: 205 kb   Fabricar: Makita  
Categoría: Tratamiento de la madera de placas
@name

SYMBOLS USD101-2 The followings show the symbols used for tool. V ....................... volts ................alternating current A .......................amperes n....................no load speed ° Hz ..................... hertz .../min................revolutions or reciprocation per minute FUNCTIONAL DESCRIPTION 003654 12 3 4 7 6 5 1. Lock lever 2. Adjusting knob 3. Depth pointer 4. Fast-feed button 5. Stopper pole 6. Fast-feed button 7. Stopper pole setting nut 003656 1 1. Nylon nut CAUTIO

Descargado: 8   Tamaño del archivo: 5 mb   Fabricar: Harbor Freight Tools  
Categoría: Tratamiento de la madera de placas
@name

Make sure the Nuts are above the mounting holes. Then, screw a Nut (24B) upward on each of the eight Hex Screws to secure the Hex Screws to the Main Table. (See Figure J.) To AttachThe Motor Assembly: 1. Lower the Adjustment Board (17D) with its pre-attached Motor Assembly through the top of the Main Table (20B). Position the Adjustment Board and Motor Assembly so that its Power Cord is on the left hand side and the Spindle Lock Lever (22E) is on the right hand side. Continue lowering the Adjust

Descargado: 0   Tamaño del archivo: 256 kb   Fabricar: Avanti  
Categoría: Tratamiento de la madera de placas
@name

Rinse well and wipe dry with a clean soft cloth. CAUTION: Failure to unplug the unit could result in electrical shock or personal injury. . Power Failure Most power failures are corrected within a few hours and should not affect the temperature of your unit if you minimize the number of times the door is opened. If the power is going to be off for a longer period of time, you need to take the proper steps to protect your food. . Vacation Time • Short vacations: Leave the unit operating during va

Descargado: 0   Tamaño del archivo: 256 kb   Fabricar: Avanti  
Categoría: Tratamiento de la madera de placas
@name

Should you desire to reverse the opening direction, please call customer service for reversal instructions. OPERATING YOUR UNIT . Setting the Temperature Control • Your unit has only one control for regulating the temperature in the compartment. The temperature control is located on the upper right hand side of the compartment. • The first time you turn the unit on, set the temperature control to “6”. • The range of the temperature control is from position "OFF” to “6”. After 24 to 48 hours, adj

Descargado: 1   Tamaño del archivo: 256 kb   Fabricar: Avanti  
Categoría: Tratamiento de la madera de placas
@name

If the power cord is damaged, have it replaced by an authorized Avanti Products service center. . Extension Cord Because of potential safety hazards under certain conditions, it is strongly recommended that you do not use an extension cord with this unit. However, if you must use an extension cord it is absolutely necessary that it be a UL/CUL-Listed, 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and

Descargado: 0   Tamaño del archivo: 256 kb   Fabricar: Avanti  
Categoría: Tratamiento de la madera de placas
@name

3. Evite luz directa del sol o calor. La luz directa del sol puede afectar la capa de pintura. Las fuentes de calor en su proximidad causaran un consumo mayor de electricidad. 4. Para un mejor desempeno, nivele el refrigerador utilizando las patas ajustables o tornillos niveladores. Para verificar el nivel, abra la puerta hasta la mitad, debe regresar sola. INSTRUCCIONES PARA LA CONEXION A TIERRA Este aparato electrodomestico debe estar conectado a tierra. En caso de un cortocircuito electrico,

Descargado: 12   Tamaño del archivo: 170 kb   Fabricar: Makita  
Categoría: Tratamiento de la madera de placas
@name

Apply caution when locking tool in “ON” position and maintain firm grasp on tool. To start the tool, move the switch lever to the I (ON) position. To stop the tool, move the switch lever to the O (OFF) position. Motor unit cord 2. Outlet 3. Lock button 4. Switch trigger 003663 For RD1100 and RD1101 1 CAUTION: • Before plugging in the tool, always check to see that the 2 switch trigger actuates properly and returns to the “OFF” 3 position when released. 4 • Switch can be locked in “ON” position f

Descargado: 5   Tamaño del archivo: 170 kb   Fabricar: Makita  
Categoría: Tratamiento de la madera de placas
@name

They may cause cracks in the tool base. 16. Draw attention to the need to use cutters of the correct shank diameter and suitable for the speed of the tool. 17. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD101-2 The followings show the sym

Descargado: 4   Tamaño del archivo: 130 kb   Fabricar: Makita  
Categoría: Tratamiento de la madera de placas

Descargado: 3   Tamaño del archivo: 170 kb   Fabricar: Makita  
Categoría: Tratamiento de la madera de placas
@name

If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. Table 1: Minimum gage for cord Ampere Rating Volts Total length of cord in feet 120 V 25 ft. 50 ft. 100 ft. 150 ft. More Than Not More Than AWG 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 Not Recommended GROUNDING INSTRUCTIONS This tool should be grounded while in use to protect the operator from electric shock. The tool is equipped with a three-conductor cord and three-prong grounding t





Categoría