Iniciar sesión:
Clasificado: Nombre ↑   Descargas   Tarifa   Tamaño ↑  

Cub Cadet WE 26

Descargado: 0Tamaño del archivo: 2 mb    Fabricar: Cub Cadet  
Categoría: Quitanieves

NOTE: DO NOT use primer to restart a warm engine after a short shutdown. NOTE: Additional priming may be necessary if the temperature is below 15° Fahrenheit. 3. Grasp the recoil starter handle and slowly pull the rope out. At the point where it becomes slightly harder to pull the rope, slowly allow the rope to recoil. 4. Pull the starter handle with a firm, rapid stroke. Do not release the handle and allow it to snap back. Keep a firm hold on the starter handle and allow it to slowly recoil. 5.

Cub Cadet Two Stage Snow Thrower

Descargado: 26Tamaño del archivo: 8 mb    Fabricar: Cub Cadet  
Categoría: Quitanieves

Refer to page 11 for instructions on how to properly use it. NOTE: This item is fastened with a cable tie to the rear of the auger housing at the factory. Cut the cable tie before operating the snow thrower. WARNING: Never use your hands to clean snow and ice from the chute assembly or auger housing. Lamp Wiring Harness (If equipped) The post on the cable tie attaching the lamp wiring harness to the lower handle should be plugged into the hole in the lower handle. Pull the slack portion of the w

Cub Cadet TRACTOR 5252

Descargado: 8Tamaño del archivo: 5 mb    Fabricar: Cub Cadet  
Categoría: TV

If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019. Operator’s Manual PRINTED IN U.S.A. FOR

Cub Cadet Timing Deck Striper/Roller

Descargado: 3Tamaño del archivo: 306 kb    Fabricar: Cub Cadet  
Categoría: Otras herramientas

BOX 361131 CLEVELAND, OHIO 44136-0019 Printed In USA Form No. 769-03885 (February 19, 2008) Assembly & Set-Up 3 Contents of Carton • One 42" Timing Deck Striper/Roller One Operator's Manual Assembly NOTE: On older model decks the holes used to attach the Striper/ Roller to the mowing deck will have to be drilled in order to install the attachment. 1. Remove the attached carriage bolts and flange nuts from the mounting bracket. See Fig. 1-1. Flange Nuts Carriage Bolts Figure 1-1 NOT

Cub Cadet SWE 528

Descargado: 72Tamaño del archivo: 4 mb    Fabricar: Cub Cadet  
Categoría: Quitanieves

Damage resulting from the installation or use of any part, accessory or attachment not approved by Cub Cadet for use with the product(s) covered by this manual will void your warranty as to any resulting damage. Normal wear parts are warranted to be free from defects in material and workmanship for a period of thirty (30) days from the date of purchase. Normal wear parts include, but are not limited to items such as: batteries, belts, blades, blade adapters, grass bags, rider deck wheels, seats,

Cub Cadet SW-15CC

Descargado: 2Tamaño del archivo: 1 mb    Fabricar: Cub Cadet  
Categoría: Gazonouborschiki

Read it carefully before assembly and operation of the equipment! CONGRATULATIONS on your the purchase pf your new Brinly-Hardy Lawn Sweeper! Your lawn sweeper is designed, engineered and manufactured to give you the best possible dependability and performance. CUSTOMER RESPONSIBILITIES Please read and retain this manual. The instructions enables you to assemble and maintain your lawn roller properly. And please, always observe the "Safety" instructions. TABLE OF CONTENTS SAFETY ............ ...

Cub Cadet ST432

Descargado: 1Tamaño del archivo: 10 mb    Fabricar: Cub Cadet  
Categoría: Clippers

Si no esta seguro acerca de estos procedimientos, lleve su unidad a un establecimiento de reparacion, persona o distribuidor de servicio autorizado que arregle motores para uso fuera de la carretera. NOTA: El mantenimiento, la sustitucion o arreglo de dispositivos para el control de emisiones y sistemas pueden ser hechos por cualquier establecimiento de reparacion, persona o proveedor de servicio autorizado que arregle motores para uso fuera de la carretera. ADVERTENCIA: Para evitar lesiones per

Cub Cadet Series CC3000

Descargado: 7Tamaño del archivo: 2 mb    Fabricar: Cub Cadet  
Categoría: Clippers

Usar otro tipo de linea podria causar que el motor recaliente o falle. No use nunca linea reforzada con metal, alambre, cadena ni soga, etc. Estos elementos pueden desprenderse y convertirse en un proyectil peligroso. Existen dos metodos para cambiar la linea de corte. • Bobine el carrete interior con linea nueva. • Instale un carrete interior prebobinado Bobinado del carrete interior existente 1. Sostenga la bobina exterior con una mano y desenrosque el Bump Knob en sentido antihorario (Fig. 6-

Cub Cadet Series 390

Descargado: 0Tamaño del archivo: 2 mb    Fabricar: Cub Cadet  
Categoría: Herramientas de jardín

Figure 5–9: Reverse drive belt removal. Figure 5–10: Reverse drive belt removal. 6 Off-Season Storage If the tiller will not be used for a period longer than 30 days, the following steps should be taken to prepare the tiller for storage. 1. Clean the exterior of engine and the entire tiller thoroughly. Lubricate the tiller as described in the lubrication instructions. 2. We do not recommend the use of pressure washers to clean your unit. They may cause damage to electric components, spindles, pu

Cub Cadet RT 65

Descargado: 7Tamaño del archivo: 3 mb    Fabricar: Cub Cadet  
Categoría: Herramientas de jardín

BOX 361131 CLEVELAND, OHIO 44136-0019 Printed In USA Form No. 769-03793 (January 10, 2008) RT 65 Gear Case Assembly 52 35-"^ 14 14 11 16 * 28 2 RT 65 Gear Case Assembly Ref. Part Number Description 1. 611-04074 Wheel Shaft Assembly: 33T 2. 611-0021 Tine Shaft Assembly: 18T 3. 611-0128 Jack Shaft Assembly 4. 611-0129 Input Shaft Assembly 5. 617-0058 Reverse Idler Gear Assembly: 30T 6. 617-0059 Tine Idler Gear Assembly: 30T 7. 617-0060 Tine Input Sprocket Assembly: 9T 8. 617-





Categoría